ATV61HD55M3X

Altivar 61

Variable speed drive

Pumping and ventilation machine

ATV61

55 kW 3 phases at 200…240 V

75 hp 3 phases at 200…240 V

200…240 V (- 15…10 %)

3 phases

173 A for 240 V 3 phases 55 kW / 75 hp 200 A for 200 V 3 phases 55 kW / 75 hp

Without EMC filter

With heat sink

71.9 kVA for 240 V 3 phases 55 kW / 75 hp

35 kA 3 phases

265.2 A for 60 s 3 phases

2.5 kHz

2.5…12 kHz adjustable 2.5…12 kHz with derating factor

Voltage/frequency ratio, 2 points Flux vector control without sensor, standard Voltage/frequency ratio – Energy Saving, quadratic U/f Voltage/frequency ratio, 5 points

Vector control without sensor, standard

Modbus CANopen

No impedance for Modbus

APOGEE FLN communication card BACnet communication card CC-Link communication card Controller inside programmable card DeviceNet communication card Ethernet/IP communication card Fipio communication card I/O extension card Interbus-S communication card LonWorks communication card METASYS N2 communication card Modbus Plus communication card Modbus TCP communication card Modbus/Uni-Telway communication card Multi-pump card Profibus DP communication card Profibus DP V1 communication card

Asynchronous motors Synchronous motors

170…264 V

50…60 Hz (- 5…5 %)

47.5…63 Hz

221 A at 2.5 kHz, 230 V 3 phases

0.1…500 Hz

1…100 in open-loop mode, without speed feedback

+/- 10 % of nominal slip for 0.2 Tn to Tn torque variation without speed feedback

+/- 15 % in open-loop mode, without speed feedback

130 % of nominal motor torque, +/- 10 % for 60 s

30 % without braking resistor <= 125 % with braking resistor

Frequency PI regulator

Adjustable Not available in voltage/frequency ratio (2 or 5 points) Can be suppressed Automatic whatever the load

1 LED red presence of drive voltage

<= power supply voltage

Between power and control terminals

With an IP21 or an IP31 kit : 3-strand IEC cable at 40 °C, copper 70 °C PVC Without mounting kit : 1-strand IEC cable at 45 °C, copper 70 °C PVC Without mounting kit : 1-strand IEC cable at 45 °C, copper 90 °C XLPE/EPR With UL Type 1 kit : 3-strand UL 508 cable at 40 °C, copper 75 °C PVC

AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1…LI6, PWR terminal 2.5 mm² / AWG 14 L1/R, L2/S, L3/T, U/T1, V/T2, W/T3 terminal 2 x 100 mm² / 2 x 250 kcmil PA, PB terminal 60 mm² / 250 kcmil PC/-, PO, PA/+ terminal 2 x 100 mm² / 2 x 250 kcmil

L1/R, L2/S, L3/T, U/T1, V/T2, W/T3 24 N.m / 212 lb.in PA, PB 12 N.m / 106 lb.in PC/-, PO, PA/+ 41 N.m / 360 lb.in AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1…LI6, PWR 0.6 N.m

Internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 %, <= 10 mA for overload and short-circuit protection Internal supply 24 V DC (21…27 V), <= 200 mA for overload and short-circuit protection External supply 24 V DC (19…30 V)

2

AI1-/Al1+ bipolar differential voltage +/- 10 V DC, input voltage 24 V max, resolution 11 bits + sign AI2 software-configurable current 0…20 mA, impedance 242 Ohm, resolution 11 bits AI2 software-configurable voltage 0…10 V DC, input voltage 24 V max, impedance 30000 Ohm, resolution 11 bits

Discrete input LI6 (if configured as logic input) 2 ms, +/- 0.5 ms Analog input AI1-/Al1+ 2 ms, +/- 0.5 ms Analog input Al2 2 ms, +/- 0.5 ms Analog output AO1 2 ms, +/- 0.5 ms Discrete input LI1…LI5 2 ms, +/- 0.5 ms

AI1-/Al1+ +/- 0.6 % for a temperature variation 60 °C AI2 +/- 0.6 % for a temperature variation 60 °C AO1 +/- 1 % for a temperature variation 60 °C

AI1-/Al1+ +/- 0.15 % of maximum value AI2 +/- 0.15 % of maximum value AO1 +/- 0.2 %

1

AO1 software-configurable current, analogue output range 0…20 mA, impedance 500 Ohm, resolution 10 bits AO1 software-configurable logic output 10 V, <= 20 mA AO1 software-configurable voltage, analogue output range 0…10 V DC, impedance 470 Ohm, resolution 10 bits

2

(R1A, R1B, R1C) configurable relay logic NO/NC, electrical durability 100000 cycles (R2A, R2B) configurable relay logic NO, electrical durability 100000 cycles

<= 100 ms in STO (Safe Torque Off) R1A, R1B, R1C <= 7 ms, tolerance +/- 0.5 ms R2A, R2B <= 7 ms, tolerance +/- 0.5 ms

Configurable relay logic 3 mA at 24 V DC

R1, R2 on resistive load, 5 A at 30 V DC, cos phi = 1, 0 ms R1, R2 on inductive load, 2 A at 30 V DC, cos phi = 0.4, 7 ms R1, R2 on resistive load, 5 A at 250 V AC, cos phi = 1, 0 ms R1, R2 on inductive load, 2 A at 250 V AC, cos phi = 0.4, 7 ms

7

(LI1…LI5) programmable, 24 V DC, voltage limits <= 30 V, with level 1 PLC, impedance 3500 Ohm (LI6) switch-configurable, 24 V DC, voltage limits <= 30 V, with level 1 PLC, impedance 3500 Ohm (LI6) switch-configurable PTC probe, 0…6, impedance 1500 Ohm (PWR) safety input, 24 V DC, voltage limits <= 30 V, impedance 1500 Ohm

LI1…LI5 positive logic (source), < 5 V (state 0), > 11 V (state 1) LI1…LI5 negative logic (sink), > 16 V (state 0), < 10 V (state 1) LI6 (if configured as logic input) negative logic (sink), > 16 V (state 0), < 10 V (state 1) LI6 (if configured as logic input) positive logic (source), < 5 V (state 0), > 11 V (state 1)

S, U or customized Automatic adaptation of ramp if braking capacity exceeded, by using resistor Linear adjustable separately from 0.01 to 9000 s

By DC injection

Drive against exceeding limit speed Drive against input phase loss Drive break on the control circuit Drive input phase breaks Drive line supply overvoltage Drive line supply undervoltage Drive overcurrent between output phases and earth Drive overheating protection Drive overvoltages on the DC bus Drive power removal Drive short-circuit between motor phases Drive thermal protection Motor motor phase break Motor power removal Motor thermal protection

> 1 mOhm at 500 V DC for 1 minute to earth

Analog input 0.024/50 Hz Display unit 0.1 Hz

1 RJ45 for Modbus on front face 1 RJ45 for Modbus on terminal Male SUB-D 9 on RJ45 for CANopen

2-wire RS 485 for Modbus

RTU for Modbus

20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen 4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal 9600 bps, 19200 bps for Modbus on front face

8 bits, 1 stop, even parity for Modbus on front face 8 bits, odd even or no configurable parity for Modbus on terminal

1…247 for Modbus 1…127 for CANopen

Slave for CANopen

CE

Vertical +/- 10 degree

84 kg

320 mm

920 mm

377 mm

60.5 dB conforming to 86/188/EEC

2830 V DC between earth and power terminals 4230 V DC between control and power terminals

Conforming to IEC 61000-4-2 level 3 Conforming to IEC 61000-4-11 Conforming to IEC 61000-4-6 level 3 Conforming to IEC 61000-4-3 level 3 Conforming to IEC 61000-4-4 level 4

IEC 60721-3-3 class 3C2 UL Type 1

NOM 117 GOST UL CSA C-Tick DNV

3 conforming to EN/IEC 61800-5-1 3 conforming to UL 840

IP00 conforming to EN/IEC 60529 IP00 conforming to EN/IEC 61800-5-1 IP30 on side parts conforming to EN/IEC 60529 IP30 on side parts conforming to EN/IEC 61800-5-1 IP30 on the front panel conforming to EN/IEC 60529 IP30 on the front panel conforming to EN/IEC 61800-5-1 IP41 on upper part conforming to EN/IEC 60529 IP41 on upper part conforming to EN/IEC 61800-5-1 IP54 on lower part conforming to EN/IEC 60529 IP54 on lower part conforming to EN/IEC 61800-5-1

1.5 mm peak to peak (f = 3…10 Hz) conforming to EN/IEC 60068-2-6 0.6 gn (f = 10…200 Hz) conforming to EN/IEC 60068-2-6

7 gn for 11 ms conforming to EN/IEC 60068-2-27

5…95 % without condensation conforming to IEC 60068-2-3 5…95 % without dripping water conforming to IEC 60068-2-3

-10…50 °C without derating 50…60 °C with derating factor

-25…70 °C

<= 1000 m without derating 1000…3000 m with current derating 1 % per 100 m